Product

DSGP150-2021 -50Hz

Description

Features / Benefits
Cutter Assembly

  • Hardened 440 SST (56-60 Rockwell) shredding ring and grinding impeller.
  • 8,300 cuts / second..... 1 / 2 million cuts / minute.
Impeller
  • Ductile iron casting for superior quality and long life.
  • Recessed impeller provides non-overloading performance.
  • Recessed (vortex) design reduces bearing load / increases bearing life.
  • Recessed design prevents clogging.
Shaft Seals
  • Full mechanical seal (silicon / carbide) and secondary lip seal.
Motor
  • Capacitor start / run design for assured starting, strong torque and grinding under heavy load.
  • Pressed stator for precise shaft / bearing alignment, long life.
  • Internal capacitors and start switch, no external control box required.
  • Internal overload protection.
  • Dual ball bearings (upper and lower).
Oil-filled provides
  • Constant bearing lubrication.
  • Maximum motor cooling, even temperature distribution.
 
 

KEENER GRINDER PUMPS

2 HP Grinder Pumps DSGP150-50Hz Series

Specifications
Pump Model - Pump shall be of the centrifugal type, KEENER GRINDER PUMP DSGP15050Hz Series, with an integrally built-in grinder unit and submersible type motor. The grinder unit shall be capable of macerating all material in normal domestic and commercial sewage, including reasonable amounts of foreign objects such as sanitary napkins, disposable diapers Liners, thin rubber, small wood, plastic and the like to a fine slurry that will easily pass through the pump and 1-1/4" NPT discharge.

Operating Conditions - The pump shall have a capacity of             GPM at a total head of          feet, and shall use a motor rated at 2 HP and 2800 RPM.

Pump Impeller - Ductile iron and threaded on a stainless steel shaft. The impeller shall be of the recessed vortex type to provide an unobstructed passage through the volute for the ground solids.

Grinder Construction - Both grinder impellers and shredding ring shall be of 440C stainless steel hardened to 56-60 Rockwell C. The grinder assembly shall consist of a grinder impeller and shredding ring mounted directly below the volute passage. The grinder impeller is threaded to a stainless steel shaft, locked with a screw and washer. The shredding ring shall be pressed into an iron holding flange for easy removal. The flange shall be provided with tapped back-off holes so screws can be used to push the shredding ring from the housing. All grinding of solids shall be from the action of the grinder impeller against the shredding ring. There shall be 8,300 cuts / second.

Seals - The motor shall be protected by a dual mechanical seals mounted in tandem. Type 21, (silicon / carbide) with (secondary) lip seal. The mechanical seal faces shall be silicon and carbide, lapped to a flatness of one light band.

Motor - The pump motor shall be of the submersible type, rated 2 HP, 2800 RPM. The motor shall be for 50 Hz, 240 volt, single phase operation. Single phase motors shall be capacitor start, capacitor run type for high starting torque. The motor will in corporate an electronic, mechanical starting switch. Run capacitor ratings shall not exceed 350 volts. Major operating temperature must not exceed Class “F” ratings.

The stator winding shall be of the open type with Class F insulation. Winding housing shall be filled with a clean, high dielectric oil that lubricates bearings and seals, transferring heat from windings and rotor to the outer cast housing. Air-filled motors which do not have the superior heat dissipating capabilities of oil-filled motors shall not be considered equal.

The motor shall have two heavy duty ball bearings to support the pump shaft, taking radial and thrust loadings. Ball bearings shall be designed for a minimum 50,000 hours B-10 life. The stator shall be pressed into the motor housing. The common motor pump and grinder shaft shall be of 416 SST, threaded to take the pump and grinder impeller.

Single phase motors shall have automatic reset overload protection attached to the top end of the motor windings to stop the motor if the motor winding temperature reaches
130 degrees C. The high temperature shut-off will cause the pump to cease operation, should a control failure cause the pump to run in a dry wet well. The overload shall automatically reset when the motor cools to a safe operating temperature.

Power Cord - The motor power cord shall be. SJOW / SJOWA or SOOW. The cable jacket shall be sealed at the motor entrance by means of a rubber compression washer and compression nut. An epoxy filled tube shall seal the outer cable jacket and individual leads to prevent water from entering the motor housing. Individual conductor strands shall be soldered within the epoxy seal.
 
 
 
 
 
 
 

Feature

2 HP Grinder Pump
  • Ideal for Long Discharge Runs or High Static Heads
  • Double Mechanical Seal
  • Silicon Carbide (Main) – Grit Resistant
  • Carbon Ceramic (Secondary)
  • Dual Sealing Chambers with Moisture Detection for Optimum Motor Protection Ductile iron Impeller, Recessed, Clog-Free
  • 30 Year Proven Design
  • Stainless Steel Grinder Assembly Effectively Macerates Domestic Into a Fine Slurry

Back to Previous Page